Comb-shaped diblock copolystyrene for anion exchange membranes

To improve the properties of diblock copolystyrene-based anion exchange membranes (AEMs), a series of AEMs with comb-shaped quaternary ammonium (QA) architecture (QA-PS_m-b-PDVPPA_n-xC where x denotes the number of carbon atoms in different alkyl tail chains and has values of 1, 4, 8, and 10 and C denotes carbon) were designed and synthesized via subsequent quaternization reactions with three different alkyl halogens (methyl iodide and N-alkane bromines (CH₃[CH₂] _x-1Br where x = 4, 8, and 10). Compared with triblock analogues quaternized with methyl iodide in our previous research, QA-PS_m-b-PDVPPA_n-xC (x = 4, 8, and 10) AEMs are more flexible with the introduction of a long alkyl tail chain; this probably impedes crystallization of the rigid polystyrene-based main chain and induces sterically adjustable ionic association. An increase in the pendant alkyl tail chain length generally led to enhanced microphase separation of the obtained AEMs, and this was confirmed using small-angle X-ray scattering and atomic force microscopy. The highest conductivity (25.5 mS cm⁻¹) was observed for QA-PS₁₂₀-b-PDVPPA₈₀-10C (IEC = 1.94 meq g^–1) at 20 °C. Furthermore, the water uptake (<30%) and swelling ratio (<13.1%) of QA-PS_m-b-PDVPPA_n-xC AEMs are less than half of these corresponding values for their triblock counterparts. The QA-PS₁₂₀-b-PDVPPA₈₀-10C membrane retained a maximum stability that was as high as 86.8% of its initial conductivity after a 40-day test (10 M NaOH, 80 °C), and this was probably because of the steric shielding of the cationic domains that were surrounded by the longest alkyl tail chains. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47370.     

Fabrication and optical properties of transparent LaErZr2O7 ceramic with high excess contents of La and Er

In this study, transparent LaErZr₂O₇ ceramic with high excess La and Er contents (nominally La_1.28Er_1.28Zr₂O_7.84) was successfully prepared by vacuum sintering at 1850?°C for 6?h using nanosized powder. The XRD, SEM, EDX and TEM results reveal that the single pyrochlore phase in the powder sample transforms to the coexistence of La-rich pyrochlore phase and Er-rich defect fluorite phase after high temperature sintering. The high excess amounts of La and Er favor the formation of pyrochlore structure. Despite the coexistence of two phases, the sample with 1?mm thickness shows excellent in-line transmittance in the visible to mid-infrared region (as high as 81% at 1100?nm). The upconversion and infrared emission under 980?nm exciting were measured and discussed as well.     

单晶硅表层机械力学特性的各向异性分析

为探究挠性筋结构单晶硅材料的各向异性特性以及KOH腐蚀工艺对其力学性能的影响规律,进行纳米压痕实验,并结合原子力显微镜观察单晶硅表层3个主晶面上压痕裂纹形貌随晶向的变化规律,分析单晶硅材料表层弹性模量、硬度、断裂韧性等机械力学特性参数在(001)、(110)及(111)3个主要晶面上沿各个晶向的变化规律;分析挠性筋结构单晶硅材料(001)晶面的KOH腐蚀工艺对其材料表面机械特性的影响规律.结果表明:挠性筋单晶硅在(001)晶面上弹性模量的各向异性变化幅度明显,硬度及断裂韧性各向异性的变化幅度不大;挠性筋单晶硅在(110)晶面弹性模量和断裂韧性的各向异性变化幅度明显,硬度各向异性变化幅度不大;挠性筋单晶硅在(111)晶面硬度值、弹性模量及断裂韧性参数的变化幅度幅值均较小;确定了单晶硅表层3个晶面裂纹最易扩展的晶向方向,KOH腐蚀工艺使得单晶硅表面质量降低,腐蚀后暴露的表面微裂纹、缺陷等会使得单晶硅(001)晶面表层硬度、断裂韧性降低,从而降低了挠性筋结构的实际断裂强度.     

Composition-tunable PtCu porous nanowires as highly active and durable catalyst for oxygen reduction reaction

To accelerate the commercialization of fuel cells, many efforts have been made to develope highly active and durable Pt-based catalyst for oxygen reduction reaction (ORR). Herein, PtCu porous nanowires (PNWs) with controllable composition are synthesized through an ultrasound-assisted galvanic replacement reaction. The porous structure, surface strain, and electronic property of PtCu PNWs are optimized by tuning composition, which can improve activity for ORR. Electrochemical tests reveal that the mass activity of Pt_0.5Cu_0.5 PNWs (Pt/Cu atomic ratio of 1:1) reaches 0.80 A mg_Pt^?1, which is about 5 times higher than that of the commercial Pt/C catalyst. Notably, the improved activity of the porous nanowire catalyst is also confirmed in the single-cell test. In addition, the large contact area with the carrier and internal interconnection structure of Pt_0.5Cu_0.5 PNWs enables them to exhibit much better durability than the commercial Pt/C catalyst and Pt_0.5Cu_0.5 nanotubes in accelerated durability test.     

Features of crystal structures and thermo-mechanical properties of weberites RE3NbO7 (RE=La,Nd, Sm,Eu, Gd) ceramics

The features of crystal structures, thermo-mechanical properties and their dominant mechanisms of weberites RE₃NbO₇ were studied as high-temperature oxides. We concentrated on connections between structures and thermo-mechanical properties, the influences of bond lengths, lattice distortion degrees and microstructures on these properties were estimated. The shortening of bond length and increment of bonding strength would lead to the increase of mechanical properties. The Vickers hardness (4.5-7.8 GPa) and toughness (0.5-1.6 MPa·m^1/2) of weberites RE₃NbO₇ are enhanced by grain refinement and increment of bond strength, while crystal structures, bond lengths, and lattice distortion degrees influenced their Young's modulus (100-170 GPa). Nano-indentation was applied to test the influence of microstructures on modulus and hardness. The dominant mechanisms for mechanical properties and thermal conductivity were proposed, which was conducive to properties tailoring and engineering applications of weberites RE₃NbO₇ oxides.     

Engineering Silver-Enriched Copper Core-Shell Electrocatalysts to Enhance the Production of Ethylene and C2+ Chemicals from Carbon Dioxide at Low Cell Potentials

Copper catalysts are widely studied for the electroreduction of carbon dioxide (CO₂) to value-added hydrocarbon products. Controlling the surface composition of copper nanomaterials may provide the electronic and structural properties necessary for carbon-carbon coupling, thus increasing the Faradaic efficiency (FE) towards ethylene and other multi-carbon (C₂₊) products. Synthesis and catalytic study of silver-coated copper nanoparticles (Cu@Ag NPs) for the reduction of CO₂ are presented. Bimetallic CuAg NPs are typically difficult to produce due to the bulk immiscibility between these two metals. Slow injection of the silver precursor, concentrations of organic capping agents, and gas environment proved critical to control the size and metal distribution of the Cu@Ag NPs. The optimized Cu@Ag electrocatalyst exhibited a very low onset cell potential of −2.25 V for ethylene formation, reaching a FE towards C₂₊ products (FE_C2+) of 43% at −2.50 V, which is 1.0 V lower than a reference Cu catalyst to reach a similar FE_C2+. The high ethylene formation at low potentials is attributed to enhanced C C coupling on the Ag enriched shell of the Cu@Ag electrocatalysts. This study offers a new catalyst design towards increasing the efficiency for the electroreduction of CO₂ to value-added chemicals.     

用于疏浚工程泥浆密度测量的电阻层析成像技术

江河湖海疏浚工程对于拓展和保障航运安全、促进生态恢复、维护/改善远海岛礁环境具有不可或缺的作用.目前,在绞吸和耙吸疏浚船上,多采用射线密度计及电磁流量计对输泥密度、产量等进行在线计量,并作为实现疏浚系统自动控制的重要参量.由于射线密度计潜在的人员健康、公共安全和环保风险,在一些国家和地区已建立了放射源的有序退出机制.电阻层析成像使用安装于管壁的电极阵列获得管道内流体的电导率分布,进而推导出管道内的泥浆密度,具有无辐射、全场测量及实时可视化的优点.电阻层析成像测量系统经过特殊设计,可适应从内陆淡水到海水的巨大电导率变化.初步测试表明,电阻层析成像测量数据与射线密度计具有良好一致性,具备了作为在线泥浆密度测量的可行性.此外,ERT可提供实时的流动成像,对于提高对疏浚管道监测能力和降低堵管概率具有重要意义.     

Dielectric breakdown behavior of ferroelectric ceramics: The role of pores

Dielectric breakdown is a fundamental issue for ferroelectric ceramics. In this work, a phase-field method is introduced to study the breakdown behavior of ferroelectric ceramics with pores randomly distributed. Effects of the position and the size of pores on the breakdown behavior are analyzed. Results indicate that the position of pores, for example in grains or at grain boundaries, has a significant influence on the breakdown strength of ferroelectric ceramics. The nominal breakdown strength of ferroelectric ceramics with 2 % pores at grain boundaries is almost 50 % higher than 2 % pores in grains. Further, for ferroelectric ceramics with a certain porosity, the smaller the pore size, the higher the breakdown strength. As the nominal pore size decreases from 2.5 to 1, the nominal breakdown strength is enhanced from 0.73 to 1.16. Such results agree well with the widely accepted Gerson-Marshall model and previously published experimental observations.     

A Skin-Inspired Triboelectric Nanogenerator with an Interpenetrating Structure for Motion Sensing and Energy Harvesting

Rapid advancements in wearable electronics impose the challenge on power supply devices. Herein, a flexible single-electrode triboelectric nanogenerator (SE-TENG) that enables both human motion sensing and biomechanical energy harvesting is reported. The SE-TENG is fabricated by interpenetrating Ag-coated polyethylene terephthalate (PET) nanofibers within a polydimethylsiloxane (PDMS) elastomer. The Ag coating and PDMS are performed as the electrode and dielectric material for the SE-TENG, respectively. The Ag-coated PET nanofibers enlarge the electrode surface area, which is beneficial to increase sensing sensitivity. The flexible SE-TENG sensor shows the capability of outputting alternating electrical signals with an open-circuit voltage up to 50 V and a short-circuit current up to 200 nA in response to externally applied pressure. It is used to sense various types of human motions and harvest electric energy from body motion. The harvested energy can successfully power wearable electronics, such as an electronic watch and light-emitting diode. Therefore, the as-prepared SE-TENG sensor with a pressure response and self-powered capability provides potential applications in wearable sensors or flexible electronics for personal healthcare and human–machine interfaces.     

Fabrication and characterizations of Cr3+-doped ZnGa2O4 transparent ceramics with persistent luminescence

0.5 at.% Cr:ZnGa₂O₄ precursor was synthesized by the co-precipitation method with nitrates as raw materials, using ammonium carbonate as the precipitant. Low-agglomerated Cr:ZnGa₂O₄ powders with an average particle size of 43 nm were obtained by calcining the precursor at 900℃ for 4 h. Using the powders as starting materials, 0.5 at.% Cr:ZnGa₂O₄ ceramics with an average grain size of about 515 nm were prepared by presintering at 1150℃ for 5 h in air and HIP post-treatment at 1100℃ for 3 h under 200 MPa Ar. The in-line transmittance of 0.5 at.% Cr:ZnGa₂O₄ ceramics with a thickness of 1.3 mm reaches 59.5% at the wavelength of 700 nm. The Cr:ZnGa₂O₄ ceramics can be effectively excited by visible light and produce persistent luminescence at 700 nm. For Cr:ZnGa₂O₄ transparent ceramics, the brightness of afterglow was larger than 0.32 mcd/m² after 30 min, which is far superior to that of Cr:ZnGa₂O₄ persistent luminescence powders.